No Image
Available
Image may not reflect selected features
3194 Kit Hand Tool Tethering Kit - 1lb / 0.5kg (19664) by Ergodyne
The Squids® 3194 Hand Tool Tethering Kit includes a 3156 Coil Tool Lanyard with Single Carabiner and the 3740 Hand Tool Attachment Trap – Slips™ Variety 4-Pack. This tool tethering kit allows you to tether four different sized screwdrivers and hex key wrenches making it easy to use your tools on the job while preventing dropped objects when working at-heights.

The 3156 Coil Tool Lanyard is more than just a small tool and hard hat lanyard. Built and tested to endure tough conditions and rated to support weight up to 2lbs / 0.9kg, the coiled lanyard is made with a low-profile design and durable plastic. With the lightweight aluminum carabiner on one end and a tethering loop on the other, it easily connects to tool anchors and attachments, even while wearing gloves. The coiled tether design reduces lanyard length to prevent snag and tangle hazards. The coil stretches from a compact 12in to 48in / 30cm to 122 cm.

STRAIGHTFORWARD INSTALLATION

No additional install tools or complicated taping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect the Squids® 3156 Coil Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.

Simply poke the end of the hand tool through the orange interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. To remove the Slips™, simply push on the tab to loosen and then slide it off the shaft of the tool. No adhesive residue or mess will be left behind!

PERFECT FOR SMALL HAND TOOLS

Small hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb. based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size.
Product Specification
Item #
19664
Additional product details
Vendor Item #
19664
Industrial Category
Fasteners
Industrial Subcategory
Fastener Hardware
Industrial Subtype
Lanyards
application
Military and law enforcementRoofing, Mechanics,Shooting Sports,Hunters,Motorcyclists,General Work,Warehousing/Distribution,Landscaping,Freight/Baggage
CsQty
1
feature10
Flexible inner core grips tool after application securing it as an attachment point
feature11
3156 Coil Lanyard features:
feature12
Low-profile durable plastic coil to withstand even the toughest conditions
feature13
Coiled lanyard design prevents snag and tangle hazards
feature14
Lightweight aluminum carabiner with manual locking screw gate
feature15
Tethering loop to securely connect to an anchor or tool attachment
feature2
Kit includes:
feature3
One Variety 4-Pack 3740 Hand Tool Attachment Trap – Slips™
feature4
One 3156 Coil Low Profile Tool Lanyard with Single Carabiner
feature5
Tether four different sized screwdrivers and hex key wrenches ranging from 0.05in - 0.5in // 1.3mm - 12.5mm diameter
feature6
Maximum tethering capacity of up to 1lb / 0.5kg
feature7
3740 Slips™ features:
feature8
Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking
feature9
Swiveling exterior ring spins 360- degrees allowing screwdrivers and other rotating tools to be used without issue
ItemWt_kg
0.3375
Length_cm
20.32
OrdMult
1
Origin
CHN
Product Features
Approved to the ANSI/ISEA 121-2018 standard
Size
Kit
UofM
Each
Manufactured By
Ergodyne
Call for Price
Qty:
Add To Wishlist
Save To Compare
Availability:
  • Manufacturer availability unknown.
To: From: Subject:
Home Articles About Us Contact Us Catalog View Cart Login
Training On XOLogic Features
If you have any questions on how to use any of the available XOLogic features, use the link below. For Any Other Questions:
Fill in the form below for any questions that fall outside the scope of our existing training videos. We will respond promptly and help in whatever capacity that we can. If you would like to speak with us directly, you can reach us Monday through Friday from 8AM to 5PM Mountain standard time by calling 1 (866) 684-4134.
Customer Copy
Images
Item Details
Customer Information
Item Prices
Order Totals
Vendor Information
Order & Item Notes
Shipping Notes
Terms & Conditions
Recipient:
Reply-To:
Subject:
Images
Item Details
Customer Information
Item Prices
Order Totals
Vendor Information
Order & Item Notes
Shipping Notes
Account Rebate
Terms & Conditions
Point of Sale